Quick Answer: How do you remove codes from Kwikset 888?

How do I delete a code on my Kwikset lock?

Delete A User Code:

  1. Make sure the door is open.
  2. If you have not enabled a programming code, press and release the program button. You will hear two beeps. …
  3. Press 2 to delete a user code. …
  4. Press Kwikset.
  5. Enter the user code you wish to delete. …
  6. Enter the user code again.
  7. Press Kwikset.

How do you reset a Kwikset lock 888?

You can factory default your Kwikset Z-Wave Lock by removing the lock’s cover and then removing the lock’s battery pack to power the lock down. Then press and hold the “Program” button. Keep the button held down as you reapply power to the lock. Then wait, and press one more time to reset.

How do I change my Kwikset lock code without master code?

How do I change the mastercode on my Powerbolt 2?

  1. Make sure the lock is unlocked and the door is open.
  2. Enter your Mastercode – for new install, default is 0-0-0-0.
  3. Press the lock button. You will hear one beep.
  4. Press 7.
  5. Press the lock button. You will hear one beep.
  6. Enter a new Mastercode. …
  7. Press the lock button.
IT IS IMPORTANT:  Best answer: What is a single leaf door?

How do I change the master code on my Kwikset 888?

How do I enable/delete the mastercode on my Smartcode?

  1. Keep door open. Press and HOLD the Program button until the keypad flashes green (about 5 seconds).
  2. Enter new Mastercode.
  3. Press Lock button once.
  4. Re-enter Mastercode.
  5. Press Lock button once. …
  6. Make sure switch #3 is on, and press the Program button once.

How do you program a Kwikset 888?

This is useful if the lock is being moved to a different door.

  1. Remove battery pack.
  2. Press and HOLD the program button while reinserting the battery pack. Release button once battery pack is installed. The status LED will flash red and green.
  3. Press the program button once more.

How do I remove the code from my Weiser Smart Lock?

While the door is open, test the user code to make sure it no longer unlocks the door. 2 Press Lock button once. 4 Press Lock button once. 3 Enter user code to be deleted.

How do I reset the master code on a Kwikset 913?

How do I program my SmartCode 913 lock?

  1. Open the door.
  2. Remove battery cover.
  3. Press the program button once.
  4. Enter new user code.
  5. Press lock button.
  6. If programming is successful the keypad will flash green once, and you will hear one beep.

How do I remove a code from Kwikset SmartCode 909?

Deleting a user code In order to delete a user code, you must override the code by adding a different user code in the same position. For example, if you want to delete the third code, add a different user code in position three. NOTE: Test the old user code to make sure it can no longer unlock the door.

IT IS IMPORTANT:  How much does it cost to have a Prehung door installed?

How do I reset my Kwikset 910 lock code?

Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red. Press the Program button once more. When the LED flashes green and you hear one beep, the lock has been reset.

How do you unlock a Kwikset lock code?

To program the first user code:

  1. Press the button marked “program button” once.
  2. Using the keypad, enter a 4- to 8-digit code.
  3. Press the ‘LOCK” button to save the code.
  4. Extend the bolt by pressing- the “LOCK” button.
  5. Enter the new code number. The bolt should retract.