How do I reset the door lock on a Whirlpool Duet washer?

Pressing the power button cancels the “Fan Dry” option and unlocks the door. Press the “Drain and Spin” button on the washer’s control panel to attempt to unlock the machine. This may drain any excess water that could cause the machine to remain locked. Once the “Drain and Spin” cycle completes, the door should unlock.

How do I unlock the door on my Whirlpool Duet washer?

How to Unlock a Whirlpool Duet Washing Machine

  1. Reach up inside the front panel and locate the door latch assembly on the right side of door.
  2. Feel for a tear-drop shaped tab on the bottom of the door latch assembly. This tab will manually unlock the door.
  3. Gently pull down on tab about 1/4 inch or until you hear a click.

How do I reset my Whirlpool Duet washer?

Unplug the washer for 30 seconds to attempt to reset the Duet washer control. if your fill hoses have a flood stop check valve turn the water off, disconnect the hoses and run a little water into a bucket. Then reconnect the hoses to your washer and do a Duet Washer Quick Diagnostic Test.

IT IS IMPORTANT:  Your question: How much do barn doors cost?

How do you reset the door lock on a Whirlpool washing machine?

Unplug your Whirlpool washer and leave it unplugged for 45 minutes. After 45 minutes, plug your washer back in. The washer’s programming should be reset and the door should open.

How do you reset controls locked on Whirlpool Duet washer?

How to Unlock the Controls for a Whirlpool Duet Washer

  1. Locate the “Control Lock/Unlock” button on your Duet’s control panel.
  2. Press and hold the “Control Lock/Unlock” button for three seconds.
  3. Release the “Control Lock/Unlock” button when the control lock icon on the display disappears.

How do you manually unlock a Whirlpool front load washer?

Press the “Drain and Spin” button on the washer’s control panel to attempt to unlock the machine. This may drain any excess water that could cause the machine to remain locked. Once the “Drain and Spin” cycle completes, the door should unlock.

What do you do when your Whirlpool washer won’t unlock?

If manually resetting your washer didn’t work, you should unplug the washer for 45 minutes or longer and then plug it back in. The washer’s programing should completely reset. You can now see if the door has unlocked. If your washer door is still locked, the last option is to manually unlock it.

Is there a reset button on a whirlpool front load washer?

How to Confirm You Have Reset Your Whirlpool Washing Machine. … Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.

IT IS IMPORTANT:  How do you build an exterior door insulated?

How do you run a diagnostic on a Whirlpool Duet washer?

Whirlpool Duet Diagnostic Test Mode

Close the washer door. Select any one key except “Stop/Cancel” and Control Lock. If you got it right all the lights on the Duet washer’s control should light up, and any error codes in the washer’s memory will be displayed.

Why is my washer locked and won’t open?

Turning off the machine at the mains should allow the door lock to cool down and open after a few minutes. … The most common cause is water left in machine. Try running a spin/drain cycle. If this fails, the machine can be drained by placing the washing machine drain hose lower than the drum (into a bucket or tray).

How do I turn off the Control Lock on my whirlpool washer?

To turn off Control Lock, press and hold the Options key that says “Control Lock Hold 3 Sec” under it for 3 seconds.

How do you fix a whirlpool washer that won’t drain?

What to Do When Your Washing Machine Won’t Drain

  1. Perform a Master Reset. Unplug your washer for about one minute. …
  2. Test the Lid Switch Assembly. …
  3. See if the Drain Hose is Kinked. …
  4. Check the Drain Hose or Pump for Clogs. …
  5. Clean out the Coin Trap. …
  6. Check the Water Level Control. …
  7. Schedule Washing Machine Repair.